Are you one of them searching for “How to Fix Foger Switch Pro Vape” and looking to find a solution? You are in the right place. Foger Switch Pro vape might sometimes have issues like not hitting or charging, burnt taste, auto-firing, weak vapor, or no vapor production. Fixing a Foger Switch Pro 30K isn’t as difficult as you might think. Our step-by-step guide will help you fix the most common problems that vapers have with their Foger Switch Pro vapes, and our troubleshooting tips will act as your handy companion with some quick solutions. Let’s discuss more in detail.

With a detachable battery unit, the Foger Switch Pro 30K stands out for its innovative design. The battery boasts an impressive 1050mAh capacity, split between a rechargeable 850mAh battery in the battery pack and a 200mAh battery in the pod unit. The pod unit charges while connected to the battery, ensuring you’re always ready for a smooth vape session.

One of the key features of this vape is its transparent e-liquid tank, which lets you monitor your juice levels. It also includes a side-mounted OLED display panel that tracks both the puff count and battery level. You’ll always be in the know when it comes to your vaping progress. Additionally, the Foger Switch Pro 30K supports both Norm and Boost modes, giving you versatility in your vaping experience.

When your Foger Switch Pro Kit 30K doesn’t hit, it’s one of the most frustrating issues. The following list states the possible causes and how to fix this issue:

•  Dead Battery: The battery pack or pod unit might have run out of charge.

•  Blocked Airflow: Debris in the airflow vents or blocking the airflow sensor with your hand.

•  Loose Connection: Loose internal wiring causing poor or no connection between the battery pack and the pod unit.

• E-liquid Flooding: Chain vaping on FOGER Switch Pro vapes causes flooding, i.e., over-saturating the coil with e-liquid.

1.  Charge the Battery: Connect the battery pack to the charger and pair with the pod to charge the two units simultaneously. (Make sure the battery pack is charged so that it can charge the pod unit. When the two units are paired, the pod will start to recharge only when the battery is connected to the charger. This way, the units get charged simultaneously.)

2.  Clear the Airflow: Blow into the mouthpiece gently to loosen the blockage.

3.  Take Hard Pulls: A few hard pulls should release the small clogs in the airflow sensor.

4.  Shake the Vape: Shaking the vape pen gently could release the e-liquid inside the coil if the e-liquid is flooded.

5.  Let It Rest: Let the coil rest for a few minutes to allow it to absorb the e-liquid if you chain vape.

If your vape isn’t charging, check these possible causes and fixes:

•  Dirty Charging Port: Dust and other debris clog the charging port.

•  Faulty Cable or Adapter: Damaged or defective charging cable or adapter.

•  Battery Failure: Internal battery failure.

•  Excessive Use:Diminishes battery life and causes overuse or overheating.

1.  Clean the Charging Port: Remove the battery and use a dry cotton swab to clear any dust or other debris from the charging port.

2.  Try a Different Cable and Adapter:Try using a different charging cable and adapter to rule out a charging port problem.

3.  Charge it for 30 Minutes: Charging it for at least 30 minutes will wake the battery back up if the battery is completely dead.

4.  Try Another Power Source: Plug the charger into a different socket or use a power bank.

If you are facing weak or no vapor production, here are some possible causes and how to fix them:

•  Low E-liquid Level: Low e-liquid level.

•  Burnt Coil: The coil is clogged or burnt.

•  Weak Battery: Weaker battery.

•  Airflow Blockage: Mouthpiece or airflow vents are blocked.

1.  Check E-liquid Level: The Foger Switch Pro 30K tank is transparent, so you can check the e-liquid level by looking through it. If the e-liquid is empty, you need to change your pod unit.

2.  Give It a Break: If you are chain vaping, let the coil rest for a few minutes.

3.  Clean the Airflow Vents: Clear any debris from the mouthpiece and the airflow vents.

4.  Recharge Battery: If the battery isn’t fully charged, charge it again for better performance.

5.  Tap the Vape: Tap the vape pen gently to release any trapped air bubbles from the e-liquid chamber.

A burnt taste is a sign of an issue with the coil or e-liquid levels. Here’s how to fix it:

•  Dry Coil: The coil may not be saturated with enough e-liquid.

•  Chain Vaping: Overuse can cause the coil to overheat.

•  Low Battery: A weak battery might not heat the coil evenly.

1.  Let the Vape Rest: Give it a break for a few minutes to allow the coil to soak up e-liquid.

2.  Avoid Chain Vaping: Take slower, spaced-out puffs to prevent overheating.

3.  Check the E-liquid Level: If the tank is empty, it’s time to refill.

4.  Shake the Device: This helps distribute the liquid evenly across the coil.

5.  Charge the Battery: Make sure the battery is fully charged for consistent heating.

If your Foger Switch Pro Pod 30K is firing on its own, this could be a malfunction of the airflow sensor or internal wiring.

•  Malfunctioning Airflow Sensor: The sensor might be stuck.

•  Internal Short Circuit: Faulty wiring could cause misfires.

1.  Blow into the Mouthpiece: Clear any blockages in the airflow sensor.

2.  Store it in a Cool Place: Excessive heat may cause misfires.

If these fixes don’t solve the problem, it may be time to replace the device.

The Foger Switch Pro 30K is a versatile and durable vaping device, but like any product, it can face issues over time. You now know how to fix your Foger Switch Pro vape.

Buy the Foger Switch Pro Kit! You can find the latest deals and accessories at FogerVapeOfficial.

Our customer support team is here to help. Reach out via email at support@fogervapeofficial.com or check out our blog section for more information.